...And flywheel solutions!

I removed all the dowel pins from the crankshaft, which wasn't super difficult this time around... I think my holes are a light press fit, rather than the super-tight holes that were there originally. I'm not sure if that'll cause problems down the road or not; they are still a press fit, so load should (theoretically?) be transferred just as effectively.

The flywheel face on the crankshaft seemed to have zero runout when sitting in the crankcase, but there were a few problems with how I was taking that measurement that could have absorbed imperfections... so I decided to throw it at the lathe and check runout by painting the face with red dykem and scraping a tool along the face. The goal was to avoid removing any material, just rub the dykem off, and see if it was a gnarly edge on a dowel hole that was causing issues, or if the face itself was not perpendicular to the axis of rotation. I thought I took a picture of the result, but apparently this was another instance where my phone shut off instead of taking a picture... that's been happening a lot recently.

Anyways, the dykem was scraped off of about half the face, and the other half the dykem was still there; it made almost a perfect half circle of red and a half circle of steel. Now, the crankshaft was out about .0005 on each end, and I failed to document whether it was out the same direction at the same point in rotation; so when I did the math, I had to assume worst-case of the crankshaft being out a full thousandth of an inch. Even so, the pattern was much too extreme to blame it on a misalignment of that magnitude, so I turned a couple thousandths off the entire face. When I re-attached the flywheel, it was only out about 1 thousandth of an inch as opposed to the 8 I had before, so I put the dowels back in and put the flywheel back on. I put the whole thing on the lathe as an assembly, because I have to do a little more work on the flywheel.

Now to the part I have pictures of! The final flywheel is going to be two parts riveted together. The inside part will be turned from the original flywheel, and the outside is from a much lighter flexplate (which basically just positions the ring gear and transfers the load from the starter.) I cut the inside out of the flexplate on a CNC mill at work, since it was too big to turn on the lathe.

I also cut the outside off of the flywheel on the mill, but left it oversize so I could finish it on the lathe.

I could have programmed the mill to cut a circle, but I wanted to use a rotary table to get a true circle on the flexplate, since I can't touch that up on the lathe. Once I was set up to do that, it was just easier to do the same with the flywheel.

Once the flywheel and crankshaft assembly were on the lathe together, I started working towards the final shape. There's a step on the outside of the flywheel that needed to be turned flat with the rest of the face, and then a new step needed to be cut out from 5" diameter outwards to accept the flexplate. I've got the whole thing turned flat, and I used some red dykem to help me visualize where that 5" diameter will be.

It's been a little tough to find time to work on this stuff, but I think I see the light at the end of the tunnel. I have a few more parts on order, and once they get here I should be able to begin the reassembly process... which should be a pretty quick process, given how much documenting and adjusting and tweaking I've done *before* started to put it all together.

Slow progress, but promising results!

A few months ago, my wife and I relocated to Rochester, NY for work, and to be closer to her family.

A small part of my new job is machining odd parts on a Tormach 1100, a 2.5 axis CNC mill. As a result, I'm now able to make *much* nicer and more complex parts than I could on my drill press in my shop back in PA. Which is really handy, since I ruined a couple of custom pieces taking this engine apart.

This is a two-piece housing that holds an oil seal. All of the information I could gather said that this should be attached in a way that prying and application of heat would allow its removal. All of that information was incorrect, as it turns out. Several #6 screws, hidden by RTV sealant and covered with paint, held this assembly on. I managed to bend it during my first failed attempt at removal, but even worse, I scraped the sealing face pretty bad with the screwdriver I was using to pry it off. As a result, I needed to replace both pieces.... and it just so happens I now have the tools to do so.

I didn't take a lot of pictures, but here's a shot of an aluminum blank next to one of the (almost) finished pieces:

I think the originals were turned on a lathe, based on the finish on the old parts vs the finish on the new parts. (Admittedly, I am not what most would call a competent machinist, so maybe I just failed to produce a quality part.) However, I think the new pieces will work out just fine.

According to the book I'm reading, "How to Rebuild your Volkswagen Aircooled Engine," Tom Wilson says the best way to clean the aluminum/magnesium engine case is with regular old soap.... with phosphate. Probably wasn't hard to come by when the book was written, but now it seems nobody sells it. I'm going to try regular old soap without phosphate, and see what happens. I'll be taking my crankshaft in next week to have it magnafluxed, and if it passes I'll be placing my big order for engine parts. My hope is that the engine will go back together pretty quickly, since there was no apparent damage and it ran ok before. 

As explanation for my apparent lack of significant progress, allow me to placate you with a picture of my son, who was born a few weeks ago, and has been eating up all of my time. Strangely, I don't mind....