Starting to prep for assembly.... sort of.

With my crankshaft back and polished, I was able to begin reassembling the gears onto the nose.  First the key:

Heat up the cam drive gear, and slip it on:

Next the spacer and the new brass distributor gear.

I'm working out the best way to attach the prop hub - I know what orientation, but if I want it repeatable to exactly the same spot, I'll need to build some kind of jig that locates off of the cam drive gear. I'm not sure how much that will matter at this point.

In the meantime, I finished walnut blasting the case, and decided to try it on the heads as well. They were somewhat improved, but I'll still try soaking them in carb cleaner to try and get rid of more of the carbon that's built up. Ignore the ape blocking part of the picture...

And below, a chamber in progress to show my future self that it was, in fact, having an effect:

Once everything was sufficiently blasted, I used Simple Green to clean the case as best I could. I'll admit, I focused a little more on the outside than the inside, but I think it's pretty clean all the way through.

Once clean and dry, I cleaned the outside with solvent and got ready to paint. Bob Hoover says three things about painting the case: Do it, do it black, and do it thin. When I got the case, it was painted a dark gray... over top of a dark blue. Two layers of paint, the outer one fairly thick, were definitely not going to help much with thermal transfer, and yet it still flew that way. In light of that fact, I took Bob Hoover's advice on two of the points: I painted it, and I painted it thin.... and I painted it red.

I figure the color is less important than the paint thickness, so I cut the paint with Naptha and brushed it on, making sure to run the brush over any areas that looked like they had extra paint. The end result is definitely brush-textured, and not exactly what I had envisioned, but it looks pretty nifty all the same... and more importantly, it's protected from corrosion and it's not likely to overheat from the paint. I'll put this in the oven like I did the cylinders to get the paint nice and hard... it makes a big difference!

Rust removal sucks, Cleaning sucks, Painting sucks...

....but they're all pretty necessary if this engine is going to last. So I've been doing due diligence to remove corrosion, clean up, prep, paint, and heat treat all my engine components according to best practices as instructed by Bob Hoover and Tom Wilson. There's a fantastic resource online at http://www.eaa691.net/images/pdf/VW%20aircraft%20engine%20building.pdf , which is a hundred some pages on what to do, why to do it, and what happens when you don't. I've been just collecting parts and trying to get everything ready for the first trial assembly. Tomorrow I'm taking my crankshaft in to have it magnafluxed, and if it comes back ok I'll start putting stuff back on it. First the woodruff key and the gears, then the prop hub. The next step will be installing the bearings in the crank case, and dropping crank and camshaft, along with some associated hardware, inside and making sure it all turns the way I want it to. 

I got new cylinders and pistons, measured them, weighed them, cleaned them *very* well, and painted them black to prevent corrosion and encourage heat transfer. 

The cylinder on the left has wet paint on it, the cylinder on the right has been cleaned but not painted yet. I made sure to keep track of the cylinders, and marked them after they were painted so I could keep track of them.

As it turns out, the cylinders I designated as "A" and "D" were both 4.490" between the two sealing surfaces, whereas cylinders "B" and "C" were slightly shorter at 4.487". That's right on the edge of too much difference, but because I've got less than a half a thousandth of difference between matching cylinders, I'm not going to send them out to have them machined. Instead, I'll put both of the "long" cylinders on one side, so the heads will be able to seal correctly, and either make up the difference between the two sides with a .003 shim, or just not worry about it.... for all I know, once it's assembled, other tolerances may stack up and either make it a larger difference or even it out. That's why I'm calling this a "trial" assembly, because there may be adjustments to make after it's all together. 

I'm working on removing some surface rust on my prop hub with vinegar. Most of it came off after soaking for about two hours, but I'll give it another shot tomorrow after work. I still have a fair amount of cleaning to do on the engine case, which is about the last thing I want to do... but it's going to be the thing that's holding me up in just a few days, I think. By next week, I hope to be posting pictures of a freshly painted, partially assembled engine.